Products

Exterior Wall Systems

PUCCS NC (NON-COMBUSTIBLE) (Patent Pending)

DuROCK’s PUCCS NC is the latest addition to the PUCCS series of Exterior insulated Finish Systems. The GDDC circular grooved PUCC-ROCK virgin wool insulation board has a 10mm deep air space required by building code and professional insurers. PUCC-ROCK non-combustible insulation and its integral reinforcing mesh are simultaneously fastened to the supporting wall using DuROCK’s liquid applied WRB’s and mechanical fasteners. The PUCC-ROCK insulation board effectively forms a water-repellant gasket around each fastener. PUCC-ROCK insulation boards are face-marked at 4 inch intervals to pinpoint stud locations, which makes this system much easier and faster to install. PUCCS NC has dual reinforcing meshes for increased impact resistance. PUCCS NC liquid-applied WRB’s effectively control air leakage, yet permit vapour diffusion to the exterior. PUCCS NC can be easily detailed to direct precipitation to the exterior.

PUCCS EIFS FOR COMMERCIAL AND HIGH RISE

PUCCS is continuous insulation cladding that includes a Geometrically Defined Drainage Cavity (GDDC) that is 10 mm deep and 37% open. PUCCS complies with National Building Code of Canada Subsection 5.9.4 (OBC 5.10.3) and Subsection 9.27.13, PUCCS complies with the CAN/ULC-S716.1 EIFS Materials and Systems test standard, PUCCS satisfies the test criteria in National Building Code of Canada Article 3.1.5.5 when tested in accordance with CAN/ULC-S134, and PUCCS satisfies the test criteria in National Building Code of Canada Article 3.2.3.8 when tested in accordance with CAN/ULC-S101.

Barrier Coats

POLAR BEAR

DuROCK Polar Bear is formulated with a 100% acrylic emulsion. It is a trowel-applied high performance coating for use over wood substrates as both an air and moisture barrier, in particular for the DuROCK PUCCS RMC-1 and InsulROCK RMC-1 Systems. Polar Bear contains fibers that enhance the cohesive and tensile strength for added durability. Polar Bear can also be used as an insulation adhesive. The low water absorption combined with a high flexural strength makes Polar Bear an ideal water penetration barrier for use on exterior wall systems; in particular plywood 12.7 mm (½ inch) thick and oriented strand board (OSB), minimum 11.1 mm (7/16 inch) thick.

CEMENT BEAR

DuROCK Cement Bear is formulated with a 100% acrylic emulsion that is field-mixed with Portland Cement. It is a trowel-applied high performance coating for use on non-combustible substrates, as an air and moisture barrier for DuROCK PUCCS and InsulROCK Systems. Cement Bear contains fibres that enhance the cohesive and tensile strength for added durability. Cement Bear can also be used as an insulation adhesive. The low water absorption combined with a high flexural strength makes Cement Bear an ideal water penetration barrier for use on exterior wall systems; in particular glass-fibre faced gypsum sheathing, cement board, concrete or masonry substrates.

Leveling Coats

ONE STEP READY MIX

DuROCK One Step Ready Mix is a formulated dry-mix cement parging, leveling coat and stucco base coat that is field-mixed with water. It is a trowel-applied polymer modified cement plaster, a mixture of Portland cement, silica sand, and dry-resins. It is a versatile product that can be used as a leveling coat for conventional stucco, concrete and masonry substrates, and also as the scratch and brown coats for DuROCK Stucco Plus.One Step Ready Mix has the benefit of high-early compressive and tensile strength, with excellent freeze-thaw stability and low water absorption. It is a convenient product since it requires only water to be added on site.

ONE STEP CONCENTRATE

DuROCK One Step Concentrate is a formulated dry-mix concentrate for use in cement parging, leveling coats and stucco base coats. It is field-mixed with Portland cement, silica sand and water. One Step Concentrate is a trowel or spray-applied polymer modified cement plaster, a mixture of minerals, fine aggregates, and dry-resins. It is a versatile product that can be used as a leveling coat for conventional stucco, concrete and masonry substrates, and also as the scratch and brown coats for DuROCK Stucco Plus.One Step Concentrate has the benefit of high-early compressive and tensile strength, with excellent freeze-thaw stability and low water absorption.

Base Coats & Adhesives

B2000

DuRock B2000 is an acrylic-modified cementitious dry mix base coat designed for use over Expanded Polystyrene (EPS) Insulated Concrete Forms (ICF). B2000 forms a strong yet flexible, crack resistant base coat that is intended for use on the exterior, above-grade portion of ICF foundation walls. B2000 has high flexural and bond strength, is water vapour permeable, and has excellent freeze/thaw stability with low water absorption and low shrinkage.

PREP COAT

DuROCK Prep Coat is 100% acrylic emulsion that is field-mixed with Portland Cement. It is a trowel-applied high performance coating for use on DuROCK PUCCS and InsulROCK Systems as a non-combustible base coat and adhesive. Prep Coat is a flexible and durable base coat that can also be used as a leveling coat for stucco, concrete and masonry substrates. It has excellent freeze-thaw stability, low water absorption, breathable to water vapour and non-combustible. It is a convenient product since it requires only water to be added on site.

PREP COAT PLUS

DuROCK Prep Coat Plus is 100% styrene acrylic emulsion that is field-mixed with Portland Cement. It is a trowel-applied high performance coating for use on DuROCK PUCCS RMC and InsulROCK RMC Systems as a base coat and adhesive with enhanced flexibility and strength. Prep Coat Plus is a flexible and durable base coat that can also be used as a leveling coat for stucco, concrete and masonry substrates. It has excellent freeze-thaw stability, low water absorption, and breathable to water vapour. Prep Coat Plus can be applied as a high-build leveling coat, for added impact resistance on EIFS or to make a wall plumb and flat, applied up to 6.4 mm (1/4 inch) thick in a single pass if required.

PREP COAT D

DuROCK Prep Coat is dry polymer based dry-mix material that is field-mixed with water. It is a trowel-applied high performance coating for use on DuROCK PUCCS and InsulROCK Systems as a non-combustible base coat and adhesive. Prep Coat D is a flexible and durable base coat that can also be used as a leveling coat for stucco, concrete and masonry substrates. It has excellent freeze-thaw stability, low water absorption, breathable to water vapour and non-combustible. It is a convenient product since it requires only water to be added on site.

PREP COAT Q

DuROCK Prep Coat Q is a fast drying, dry polymer based dry-mix material that is field-mixed with water. It is ideal for use in cold temperature, high humidity conditions. It is a trowel-applied high performance coating for use on DuROCK PUCCS and InsulROCK Systems as a non-combustible base coat and adhesive. Prep Coat Q is a flexible and durable base coat that can also be used as a leveling coat for stucco, concrete and masonry substrates. It has excellent freeze-thaw stability, low water absorption, breathable to water vapour and non-combustible. It is a convenient product since it requires only water to be added on site.

PERFECT PARGE

DuROCK Perfect Parge is a polymer based dry-mix material that. It is a trowel-applied adhesive for use in the attachment of decorative moldings and EPS trim on DuROCK PUCCS and InsulROCK Systems. Perfect Parge is a flexible and durable base coat that can also be used as a leveling coat for stucco, concrete and masonry substrates. It has excellent freeze-thaw stability, low water absorption, breathable to water vapour and non-combustible. It is a convenient product since it requires only water to be added on site.

PREP COAT NCP

DuROCK NCP, Non-cementitious Prep Coat, is formulated with a 100% styrene acrylic emulsion. It is a trowelapplied high performance coating for use as an optional base coat on the DuROCK PUCCS RMC and InsulROCK RMC Systems, as well as the DuROCK Exterior Finish Systems. NCP is a factory-mixed base coat that does not require the addition of water or Portland cement.

Finishes

TROWEL FINISHES

DuROCK Trowel Finishes are premixed, water-based, 100% acrylic coatings available in several textures and unlimited colours. DuROCK Trowel Finishes are flexible, breathable, water-repelling, dirt pick-up resistant (DPR), ultra-violet resistant finishes consisting of granulated quartz or marble, pigment, resin and other additives specially formulated for both exterior and interior use. DuROCK Trowel Finishes are ideally suited for both new and/or retrofit construction. DuROCK Trowel Finishes are available in several textures distinguished by their aggregate size and application technique. Coarse Coat, Desert Sand, Grain, Marble Coat, Max Coat, Pebble Rock, Sand Coat, Spacco, and Venetian finishes are trowel-applied coatings designed for use over wall and ceiling areas. Fine Coat and Pebble Coat finishes are trowel-applied coatings designed for use over details such as cornice, quoins, columns, etc.

SPRAY FINISHES

DuROCK Spray Finishes are premixed, water-based, 100% acrylic coatings available in several textures and unlimited colours. DuROCK Spray Finishes are flexible, breathable, water-repelling, dirt pick-up resistant (DPR), ultraviolet resistant finishes consisting of silica sand, pigment, resin and other additives formulated for both exterior and interior use. DuROCK Spray Finishes are ideally suited for both new and/or retrofit construction. Whereas Pebble Spray and Fine Spray are intended for details only, the remaining DuROCK Spray Finishes are designed for use over wall and ceiling areas.

PLUS FINISHES

DuROCK Plus Finishes are formulated with 100% acrylic emulsions designed especially for use in elastomeric wall coatings, providing outstanding exterior durability, as well as excellent elasticity and elongation properties that are required to bridge continually over cracks without wrinkling. Due to the low glass-transition temperature, these finishes are able to maintain flexibility across a broad range of temperatures.DuROCK Plus Finishes can be color-tinted, and are intended for application on vertical wall surfaces. These finishes are most effective when applied over rigid substrates (such as cement plasters and concrete), and can also be used with DuROCK EIFS and Exterior Finishing Systems. DuROCK Plus Finishes are formulated to have excellent dirt-pick-up resistance, and superior water resistance as well as resistance to chalking. The dirt pick-up resistant chemistry of DuROCK Plus Finishes enables the coating to maintain its attractive appearance, while providing superior resistance to the effects of acid rain, pollution and ultra-violet light. Water beads on the surface thereby washing away the dirt. DuROCK Plus Finishes are permeable to water vapour, which permits open vapour diffusion through wall assemblies.

ROLLER FINISHES

DuROCK Roller Finishes are premixed, water-based, 100% acrylic coatings available in several textures and unlimited colours. DuROCK Roller Finishes are flexible, breathable, water-repelling, dirt pick-up resistant (DPR), ultraviolet resistant finishes consisting of fine fillers, pigment, resin and other additives formulated for both exterior and interior use. DuROCK Roller Finishes are ideally suited for both new and/or retrofit construction. Roll On (small aggregate), Roll On Coarse (large aggregate) and Airless (no aggregate) are intended for use on decorative mouldings and a variety of wall surfaces.

Specialty Finishes

ANGELSTONE/GLITTEROCK

DuROCK Angel Stone is ideal for use in interior or exterior applications, in new construction or renovations, and in commercial, industrial, institutional and residential projects. DuROCK Angel Stone is a decorative textured protective coating engineered for use over any DuROCK system. DuROCK Angel Stone is a 100% acrylic finish containing bronze mica flakes and pearlescent pigments giving the finish a shimmering effect. DuROCK Angel Stone is a trowel-applied finish texture available in hundreds of colours.

TRICOL

DuROCK Tricol finish is a premixed, water-based, acrylic, quartz stone finish available in many colour combinations. DuROCK Tricol can be both trowel and spray-applied, used for wall and ceiling areas, as well as for details such as cornice, quoins, columns, etc.

GEMSTONE

DuROCK Gemstone finish is a premixed, water-based, acrylic, quartz stone finish available in many colour combinations. DuROCK Gemstone can be both trowel and spray-applied, used for wall and ceiling areas, as well as for details such as cornice, quoins, columns, etc.

UNIGUM

Unigum is designed for use where an elastic, waterproof, dirt-resistant coating is required. Unigum is a premixed, water-based, elastomeric acrylic coating available in unlimited colours. Unigum actually bridges cracks – spanning the crack as it expands – and returning to its original form when the crack contracts. Unigum’s ability to resist ultraviolet degradation and its low-temperature flexibility ensures it will retain its colour and overall appearance for years to come.

SPACCO

DuROCK Spacco is a decorative protective coating designed for use as a textured free hand faux finish. DuROCK Spacco is ideal for use in both interior and exterior applications, in new construction or renovations, and in commercial, industrial, institutional and residential projects. DuROCK Spacco is a 100% acrylic, flexible, breathable coating. DuROCK Spacco is a trowel-applied finish texture and upon request, can be custom coloured to match any customer-specified colour.

CRYSTAL COAT

DuROCK Crystal Coat is a gypsum-based decorative textured protective coating designed for use as a textured, free hand faux finish base coat. It has been designed to replace conventional gypsum based architectural wall finishes. DuROCK Crystal Coat is ideal for use in interior applications, in new construction or renovations, and in commercial, industrial, institutional and residential projects. DuROCK Crystal Coat is a 100% acrylic, flexible, breathable coating.

POOL QUARTZ

Pool Quartz is a complete pool plaster mix that is a combination of white Portland cement, crushed marble, mineral fillers, additives and 3M Colour Quartz. Pool Quartz cures to a smooth, hard surface. Pool Quartz has excellent abrasion resistance and with the addition of 3M Colour Quartz it performs upwards of three times better against both mechanical and chemical wear compared to conventional plaster.

The Benefits are endless

Why Stucco?

Stucco is a multi-layered EIFS that is used on both commercial buildings and homes. It provides superior energy efficiency and reduces moisture penetration. In today’s society, energy efficiency is becoming increasingly important social and economic requirement, and the EIFS system can be an effective home energy-saving alternative. Once installed, this system is virtually maintenance free, and cost competitive.

Stucco has been used for over a century as a surface finish. It is recognized among architects and builders for its great design flexibility. The vast variety of colours, textures, and architectural detailing, such as arches, cornices, columns, keystones and other decorative accents enable architects and builders to create a striking, distinctive appearance for any building or residence

Interior Trim and Crown Molding

Other Services

Crown molding is a decorative finishing element that’s normally used for capping cabinets, columns, and, most often, interior walls at the point where the wall meets the ceiling. It’s only used at the top of a room, thus the term “crown” is used to describe the embellishment of a space.

Crown molding in your home compared with none in a similar home in your neighborhood could make a difference when it’s time to sell. “You may not get the money back, but it’s a feature that most buyers appreciate when looking for a home.

TESTIMONIAL

What Our Clients Say